Van der Waals equation/Citable Version: Difference between revisions
imported>D. Matt Innis (Van der Waals equation moved to Van der Waals equation/Draft: approved) |
imported>John Stephenson m (moved Van der Waals equation to Van der Waals equation/Citable Version: citable version policy) |
||
(3 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
{{subpages}} | |||
In [[physics]], [[chemistry]], and [[chemical engineering]], the '''van der Waals equation''' is an [[equation of state]] for a [[fluid]] composed of particles that have a non-zero size and a pairwise attractive inter-particle [[force]] (such as the [[van der Waals force]].) It was derived by [[Johannes Diderik van der Waals]] in his doctoral thesis (Leiden 1873)<ref>van der Waals, JD (1873) ''Over de Continuiteit van den Gas- en Vloeistoftoestand (on the continuity of the gas and liquid state)''. Ph.D. thesis, Leiden, The Netherlands. [http://www.scs.uiuc.edu/~mainzv/exhibit/vanderwaals.htm]</ref>, based on a modification of the [[ideal gas law]]. The importance of his work was the recognition that the gas and liquid phase of a compound transform continuously into each other. Above the [[critical temperature]] there is even no difference between the gas and the liquid phase, which is why it is proper to speak of the equation of a ''fluid'', a generic term for liquid ''and'' gas. | |||
==Equation== | |||
Consider a vessel of volume ''V'' filled with ''n'' [[mole (unit)|moles]] of particles (atoms or molecules) of a single compound. Let the pressure be ''p'' and the absolute temperature be ''T'', then the van der Waals equation reads | |||
:<math>\left(p + \frac{n^2 a}{V^2}\right)\left(V-nb\right) = nRT</math>, | |||
where | |||
:''a'' is a measure of the strength of attraction between the particles, | |||
:''b'' is the volume excluded from ''V'' by one mole of particles, | |||
:''R'' is the [[gas constant]], ''R'' = ''N''<sub>A</sub> ''k'', where ''k'' is the [[Boltzmann constant]] and ''N''<sub>A</sub> is [[Avogadro's constant]]. | |||
The van der Waals parameter ''b'' is proportional to ''N''<sub>A</sub> times the volume of a single particle—the volume bounded by the [[atomic radius]]. In van der Waals' original derivation, given below, ''b''/''N''<sub>A</sub> is four times the volume of a particle, which is seen as a hard sphere. Observe that the pressure ''p'' goes to infinity when the container is completely filled, so that there is no void space left for the particles to move. This occurs when ''V = n b''. | |||
===Illustration=== | |||
From the empirical [[crital temperature]] ''T''<sub>''C''</sub> and the empirical [[critical pressure]] ''p''<sub>''C''</sub> the constants ''a'' and ''b'' can be obtained by the equations | |||
:<math> | |||
a = \frac{27}{64}\frac{(RT_C)^2}{p_C}\quad \hbox{and}\quad b = \frac{RT_C}{8p_C} | |||
</math> | |||
The [[carbondioxide]] molecule (CO<sub>2</sub>) has<ref>J. V. Sengers and J. M. H. Levelt-Sengers, | |||
Annual Review of Physical Chemistry, vol. '''37''', p. 189 (1986)</ref> ''p''<sub>''C''</sub> = 7.37 MPa and ''T''<sub>''C''</sub> = 304.1 K = 31 ˚C , which gives | |||
''a'' = 0.366 m<sup>6</sup> Pa and ''b'' = 42.9 10<sup>-6</sup> m<sup>3</sup>. For four different temperatures the van der Waals curves are given in the following figure. The critical pressure is at 73.7 bar = 7370 kPa (is close to 73.7 atm). | |||
{{Image|Vanderwaals_equation_of_state.png|center|500px|van der Waals equation of state}} | |||
For large volume the pressure is low and the fluid obeys approximately the [[ideal gas law]] ''p V'' = ''n R T'' for all temperatures shown. If we decrease the volume, the pressure rises. Consider the (blue) [[isotherm]] of 10 <sup>0</sup>C, which is below the critical temperature. Decrease the volume until we reach the point ''B'', where condensation (formation of liquid CO<sub>2</sub>) starts. At this point the van der Waals curve is no longer physical (excluding the possibility of the occurrence of an oversaturated, metastable gas), because from ''B'' downward to smaller volume, the pressure stays constant—equal to the vapor pressure of the liquid. This behavior is given by the light-blue dashed line. Decreasing the volume further, we end at point ''A'' where all molecules are in the liquid phase, no molecules in the gas phase are left. When we now diminish the volume of the vessel, which contains only liquid, the pressure will rise steeply, because the [[compressibility]] of a liquid is considerable smaller than that of a gas. | |||
If we follow the (green) curve of critical temperature, we will meet a horizontal point of inflection (first and second derivatives of ''p'' wrt ''V'' are zero). If we follow any of the two isotherms, shown in the figure, of temperature higher than the critical temperature, we will not see any liquid-gas phase transition, the higher pressure fluid will resemble a liquid, while at lower pressures the fluid will be more gas-like. Nowhere on these higher isotherms will we see a gas-liquid interface appear. | |||
Although the maximum and minimum in the blue van der Waals curve are not physical, the corresponding equation was a great scientific achievement in 1873. Even today it is not possible to give a ''single'' equation that describes correctly the gas-liquid phase transition. | |||
==Validity== | |||
Above the [[critical temperature]] the van der Waals equation is an improvement of the ideal gas law, and for lower temperatures the equation is also qualitatively reasonable for the liquid state and the low-pressure gaseous state. However, the van der Waals model cannot be taken seriously in a quantitative sense, it is only useful for qualitative purposes.<ref>T. L. Hill, ''Statistical Thermodynamics'', Addison-Wesley, Reading (1960), p. 280</ref> | |||
In the [[phase transition|first-order phase transition]] range of ''(p,V,T)'' (where the [[liquid]] [[phase (matter)|phase]] and the [[gas]] phase are in equilibrium) it does not exhibit the empirical fact that ''p'' is constant (equal to the vapor pressure of the liquid) as a function of ''V'' for a given temperature. | |||
==Derivation== | |||
In the usual textbooks one finds two different derivations. One is the conventional derivation that goes back to van der Waals and the other is a statistical mechanics derivation. The latter has as its major advantage that it makes explicit the intermolecular potential, which is out of sight in the first derivation. | |||
===Conventional derivation=== | |||
Consider first one mole of gas which is composed of non-interacting point particles | |||
that satisfy the [[ideal gas law]] | |||
:<math> p = \frac{RT}{V_\mathrm{m}}.</math> | |||
{{Image|Van der Waals equation spheres.png|right|150px|The cyan colored spheres are two fluid particles, of diameter ''d'', in closest contact. The (black) enveloping sphere is excluded to other particles.}} | |||
Next assume that all particles are hard spheres of the same finite radius ''r'' = ''d''/2 (the [[van der Waals radius]]). The effect of the finite volume of the particles is to decrease the available void space in which the particles are free to move. We must replace ''V'' by ''V-b'', where ''b'' is called the ''excluded volume''. The corrected equation becomes | |||
:<math> p = \frac{RT}{V_\mathrm{m}-b}.</math> | |||
The excluded volume ''b'' is not just equal to ''N''<sub>A</sub> times the volume occupied by a single particle, but actually 4 ''N''<sub>A</sub> times that volume. To see this we must realize that two colliding particles are enveloped by a sphere of radius ''d'' that is forbidden for the centers of the other particles, see the figure. If the center of a third particle would come into the enveloping sphere, it would mean that the third particle penetrates any of the other two, which, by definition, hard spheres are unable to do. The excluded volume ''b''/''N''<sub>A</sub> per particle pair is 4π/3 × ''d''<sup>3</sup> = 32π/3 × ''r''<sup>3</sup>, so that the excluded volume is '''not''' 8π/3 × ''r''<sup>3</sup> (the sum of volumes of the two particles), but ''four'' times as much. | |||
It was a point of concern to van der Waals that the factor four yields actually an upper bound, empirical values for ''b'' are usually lower. Of course molecules are not infinitely hard, as van der Waals assumed, but are often fairly soft. | |||
Next, we introduce a pairwise attractive force between the particles. Van der Waals assumed that, notwithstanding the existence of this force, the density of the fluid is homogeneous. Further he assumed that the range of the attractive force is so small that the great majority of the particles do not feel that the container is of finite size. That is, the bulk of the particles do not notice that they have more attracting particles to their right than to their left when they are relatively close to the left-hand wall of the container. The same statement holds with left and right interchanged. Given the homogeneity of the fluid, the bulk of the particles do not experience a net force pulling them to the right or to the left. This is different for the particles in surface layers directly adjacent to the walls. They feel a net force from the bulk particles pulling them into the container, because this force is not compensated by particles between them and the wall (another assumption here is that there is no interaction between walls and particles). This net force decreases the force exerted onto the wall by the particles in the surface layer. The net force on a surface particle, pulling it into the container, is proportional to the number density ''C'' ≡ ''N''<sub>A</sub>/''V''<sub>m</sub>. The number of particles in the surface layers is, again by assuming homogeneity, also proportional to the density. In total, the force on the walls is decreased by a factor proportional to the square of the density and the pressure (force per unit surface) is decreased by | |||
:<math>a'C^2= a' \left(\frac{N_\mathrm{A}}{V_\mathrm{m}}\right)^2 = \frac{a}{V_\mathrm{m}^2} | |||
\quad\hbox{with}\quad a \equiv a' N^2_\mathrm{A}, | |||
</math>, | |||
so that | |||
:<math> p = \frac{RT}{V_\mathrm{m}-b}-\frac{a}{V_\mathrm{m}^2} \Longrightarrow | |||
(p + \frac{a}{V_\mathrm{m}^2})(V_\mathrm{m}-b) = RT. | |||
</math> | |||
Upon writing ''n'' for the number of moles and ''nV''<sub>m</sub> = ''V'', the equation obtains the form given above, | |||
:<math> (p + \frac{n^2 a}{V^2})(V-nb) = nRT. | |||
</math> | |||
It is of some historical interest to point out that van der Waals in his Nobel prize lecture gave credit to [[Laplace]] for the argument that pressure is reduced proportional to the square of the density. | |||
===Statistical thermodynamics derivation=== | |||
The canonical [[partition function]] ''Q'' of an ideal gas consisting of ''N = nN''<sub>A</sub> identical particles, is | |||
:<math> | |||
Q = \frac{q^N}{N!}\quad \hbox{with}\quad q = \frac{V}{\Lambda^3} | |||
</math> | |||
where <math>\Lambda</math> is the thermal de Broglie wavelength, | |||
:<math> | |||
\Lambda = \sqrt{\frac{h^2}{2\pi m k T}} | |||
</math> | |||
with the usual definitions: ''h'' is [[Planck's constant]], ''m'' the mass of a particle, ''k'' [[Boltzmann's constant]] and ''T'' the absolute temperature. In an ideal gas ''q'' is the partition function of a single particle in a vessel of volume ''V''. In order to derive the van der Waals equation we assume now that each particle moves independently in an average potential field offered by the other particles. The averaging over the particles is easy because we will assume that the particle density of the van der Waals fluid is homogeneous. | |||
The interaction between a pair of particles, which are hard spheres, is taken to be | |||
:<math> | |||
u(r) = | |||
\begin{cases} | |||
\infty &\hbox{when}\quad r < d, \\ | |||
-\epsilon \left(\frac{d}{r}\right)^6 & \hbox{when}\quad r \ge d, | |||
\end{cases} | |||
</math> | |||
''r'' is the distance between the centers of the spheres and ''d'' is the distance where the hard spheres touch each other (twice the van der Waals radius). The depth of the van der Waals well is <math>\epsilon</math>. | |||
Because the particles are independent the total partition function still factorizes, <math>Q = q^N/N!</math>, but the intermolecular potential necessitates two modifications to ''q''. First, because of the finite size of the particles, not all of ''V'' is available, but only <math>V - N b'</math>, where <math>{\scriptstyle b'\, \equiv\, b/N_\mathrm{A} = 2\pi d^3/3} </math> (excluded volume per particle). Second, we insert a Boltzmann factor | |||
<math>\exp[-\phi/(2kT)]</math> to take care of the average intermolecular potential. We divide here the potential by two because this interaction energy is shared between two particles. Thus | |||
:<math> | |||
q = \frac{(V-Nb') \, e^{-\phi/(2kT)}}{\Lambda^3}. | |||
</math> | |||
The total attraction felt by a single particle is, | |||
:<math> | |||
\phi = \int_d^{\infty} u(r) \frac{N}{V} 4\pi r^2 dr , | |||
</math> | |||
where we assumed that in a shell of thickness d''r'' there are ''N/V 4π r''<sup>2</sup>d''r'' particles. Performing the integral we get | |||
:<math> | |||
\phi = -2 a' \frac{N}{V}\quad\hbox{with}\quad a' = \epsilon \frac{2\pi d^3}{3} =\epsilon b'. | |||
</math> | |||
Hence, we obtain by the use of [[Stirling's approximation]], | |||
:<math> | |||
\ln Q = N \ln \frac{V-Nb'}{\Lambda^3} + \frac{N^2 a'}{V kT} -N\ln N + N. | |||
</math> | |||
It is convenient to take ''T'' out of Λ and to rewrite this expression as | |||
:<math> | |||
\ln Q = N\left(1+\ln\Bigg[ \frac{ (V-Nb')\,T^{3/2}}{N\Phi}\Bigg]\right) + \frac{N^2 a'}{V kT} , | |||
</math> | |||
where Φ is a constant. From statistical thermodynamics we know that | |||
:<math> p = kT \frac{\partial \ln Q}{\partial V} | |||
</math>, | |||
so that, writing | |||
:<math> | |||
a \equiv N_\mathrm{A}^2 a', | |||
</math> | |||
we get, | |||
:<math> | |||
p = \frac{NkT}{V-Nb'} - \frac{N^2 a'}{V^2} \Longrightarrow | |||
(p + \frac{N^2 a'}{V^2} )(V-Nb') = NkT \Longrightarrow (p + \frac{n^2 a}{V^2} )(V-nb) = nRT . | |||
</math> | |||
== Other thermodynamic parameters == | |||
The extensive volume ''V'' is related to the volume per particle ''v=V/N'' where ''N = nN''<sub>A</sub> is the number of particles in the system. As before, we consider structureless particles with three translational degrees of freedom only. | |||
The equation of state does not give us all the thermodynamic parameters of the system. We can take the equation for the [[Helmholtz energy]] ''A'' | |||
:<math> | |||
A = -kT \ln Q.\, | |||
</math> | |||
From the equation derived above for ln''Q'', we find | |||
:<math>A(T,V,N)=-NkT\left(1+\ln\left(\frac{(V-nb)T^{3/2}}{N\Phi}\right)\right) | |||
-\frac{n^2 a}{V}</math> | |||
This equation expresses ''A'' in terms of its [[Thermodynamic potential|natural variables]] ''V'' and ''T'' , and therefore gives us all thermodynamic information about the system. The mechanical equation of state was already derived above | |||
:<math>p = -\left(\frac{\partial A}{\partial V}\right)_T | |||
= \frac{NkT}{V-nb}-\frac{n^2 a}{V^2}</math> | |||
The entropy equation of state yields the [[entropy]] (''S'' ) | |||
:<math>S = -\left(\frac{\partial A}{\partial T}\right)_V | |||
=Nk\left[ \ln\left(\frac{(V-nb)T^{3/2}}{N\Phi}\right)+\frac{5}{2} \right]</math> | |||
from which we can calculate the [[internal energy]] | |||
:<math>U = A+TS = \frac{3}{2}\,NkT-\frac{n^2 a}{V}</math> | |||
Similar equations can be written for the other [[thermodynamic potentials]] and the [[chemical potential]], but expressing any potential as a function of pressure ''p'' will require the solution of a third-order polynomial, which yields a complicated expression. Therefore, expressing the [[enthalpy]] and the [[Gibbs energy]] as functions of their natural variables will be complicated. | |||
==Reduced form== | |||
Although the material constants ''a'' and ''b'' in the van der Waals equation depend on the fluid considered, the equation can be recast into a single form applicable to ''all'' fluids. | |||
The critical pressure and critical volume can be computed from the condition that the tangent in the critical point is horizontal and that it is a [[point of inflection]]: | |||
:<math> | |||
\left( \frac{\partial p}{\partial V}\right)_T = 0 \quad\hbox{and}\quad\left( \frac{\partial^2 p}{\partial V^2}\right)_T = 0. | |||
</math> | |||
This gives | |||
:<math> | |||
p_C=\frac{a}{27b^2}, \qquad \displaystyle{V_C=3b},\quad\hbox{and}\quad RT_C=\frac{8a}{27b}. | |||
</math> | |||
Defining the following reduced variables: | |||
:<math>p_R=\frac{p}{p_C},\qquad | |||
V_R=\frac{V}{V_C},\quad\hbox{and}\quad | |||
T_R=\frac{T}{T_C}</math>, | |||
the van der Waals equation of state given above (with ''n'' = 1) can be recast in the following reduced form: | |||
:<math>\left(p_R + \frac{3}{V_R^2}\right)(V_R - \frac{1}{3}) = \frac{8}{3} T_R</math> | |||
This equation holds for all fluids. Thus, when measured in units of the critical values of various quantities, all fluids obey the same equation of state—the reduced van der Waals equation of state. Van der Waals termed this the [[principle of corresponding states]]. | |||
==References== | |||
<references /> |
Latest revision as of 16:42, 23 September 2013
In physics, chemistry, and chemical engineering, the van der Waals equation is an equation of state for a fluid composed of particles that have a non-zero size and a pairwise attractive inter-particle force (such as the van der Waals force.) It was derived by Johannes Diderik van der Waals in his doctoral thesis (Leiden 1873)[1], based on a modification of the ideal gas law. The importance of his work was the recognition that the gas and liquid phase of a compound transform continuously into each other. Above the critical temperature there is even no difference between the gas and the liquid phase, which is why it is proper to speak of the equation of a fluid, a generic term for liquid and gas.
Equation
Consider a vessel of volume V filled with n moles of particles (atoms or molecules) of a single compound. Let the pressure be p and the absolute temperature be T, then the van der Waals equation reads
- ,
where
- a is a measure of the strength of attraction between the particles,
- b is the volume excluded from V by one mole of particles,
- R is the gas constant, R = NA k, where k is the Boltzmann constant and NA is Avogadro's constant.
The van der Waals parameter b is proportional to NA times the volume of a single particle—the volume bounded by the atomic radius. In van der Waals' original derivation, given below, b/NA is four times the volume of a particle, which is seen as a hard sphere. Observe that the pressure p goes to infinity when the container is completely filled, so that there is no void space left for the particles to move. This occurs when V = n b.
Illustration
From the empirical crital temperature TC and the empirical critical pressure pC the constants a and b can be obtained by the equations
The carbondioxide molecule (CO2) has[2] pC = 7.37 MPa and TC = 304.1 K = 31 ˚C , which gives a = 0.366 m6 Pa and b = 42.9 10-6 m3. For four different temperatures the van der Waals curves are given in the following figure. The critical pressure is at 73.7 bar = 7370 kPa (is close to 73.7 atm).
For large volume the pressure is low and the fluid obeys approximately the ideal gas law p V = n R T for all temperatures shown. If we decrease the volume, the pressure rises. Consider the (blue) isotherm of 10 0C, which is below the critical temperature. Decrease the volume until we reach the point B, where condensation (formation of liquid CO2) starts. At this point the van der Waals curve is no longer physical (excluding the possibility of the occurrence of an oversaturated, metastable gas), because from B downward to smaller volume, the pressure stays constant—equal to the vapor pressure of the liquid. This behavior is given by the light-blue dashed line. Decreasing the volume further, we end at point A where all molecules are in the liquid phase, no molecules in the gas phase are left. When we now diminish the volume of the vessel, which contains only liquid, the pressure will rise steeply, because the compressibility of a liquid is considerable smaller than that of a gas.
If we follow the (green) curve of critical temperature, we will meet a horizontal point of inflection (first and second derivatives of p wrt V are zero). If we follow any of the two isotherms, shown in the figure, of temperature higher than the critical temperature, we will not see any liquid-gas phase transition, the higher pressure fluid will resemble a liquid, while at lower pressures the fluid will be more gas-like. Nowhere on these higher isotherms will we see a gas-liquid interface appear.
Although the maximum and minimum in the blue van der Waals curve are not physical, the corresponding equation was a great scientific achievement in 1873. Even today it is not possible to give a single equation that describes correctly the gas-liquid phase transition.
Validity
Above the critical temperature the van der Waals equation is an improvement of the ideal gas law, and for lower temperatures the equation is also qualitatively reasonable for the liquid state and the low-pressure gaseous state. However, the van der Waals model cannot be taken seriously in a quantitative sense, it is only useful for qualitative purposes.[3]
In the first-order phase transition range of (p,V,T) (where the liquid phase and the gas phase are in equilibrium) it does not exhibit the empirical fact that p is constant (equal to the vapor pressure of the liquid) as a function of V for a given temperature.
Derivation
In the usual textbooks one finds two different derivations. One is the conventional derivation that goes back to van der Waals and the other is a statistical mechanics derivation. The latter has as its major advantage that it makes explicit the intermolecular potential, which is out of sight in the first derivation.
Conventional derivation
Consider first one mole of gas which is composed of non-interacting point particles that satisfy the ideal gas law
Next assume that all particles are hard spheres of the same finite radius r = d/2 (the van der Waals radius). The effect of the finite volume of the particles is to decrease the available void space in which the particles are free to move. We must replace V by V-b, where b is called the excluded volume. The corrected equation becomes
The excluded volume b is not just equal to NA times the volume occupied by a single particle, but actually 4 NA times that volume. To see this we must realize that two colliding particles are enveloped by a sphere of radius d that is forbidden for the centers of the other particles, see the figure. If the center of a third particle would come into the enveloping sphere, it would mean that the third particle penetrates any of the other two, which, by definition, hard spheres are unable to do. The excluded volume b/NA per particle pair is 4π/3 × d3 = 32π/3 × r3, so that the excluded volume is not 8π/3 × r3 (the sum of volumes of the two particles), but four times as much.
It was a point of concern to van der Waals that the factor four yields actually an upper bound, empirical values for b are usually lower. Of course molecules are not infinitely hard, as van der Waals assumed, but are often fairly soft.
Next, we introduce a pairwise attractive force between the particles. Van der Waals assumed that, notwithstanding the existence of this force, the density of the fluid is homogeneous. Further he assumed that the range of the attractive force is so small that the great majority of the particles do not feel that the container is of finite size. That is, the bulk of the particles do not notice that they have more attracting particles to their right than to their left when they are relatively close to the left-hand wall of the container. The same statement holds with left and right interchanged. Given the homogeneity of the fluid, the bulk of the particles do not experience a net force pulling them to the right or to the left. This is different for the particles in surface layers directly adjacent to the walls. They feel a net force from the bulk particles pulling them into the container, because this force is not compensated by particles between them and the wall (another assumption here is that there is no interaction between walls and particles). This net force decreases the force exerted onto the wall by the particles in the surface layer. The net force on a surface particle, pulling it into the container, is proportional to the number density C ≡ NA/Vm. The number of particles in the surface layers is, again by assuming homogeneity, also proportional to the density. In total, the force on the walls is decreased by a factor proportional to the square of the density and the pressure (force per unit surface) is decreased by
- ,
so that
Upon writing n for the number of moles and nVm = V, the equation obtains the form given above,
It is of some historical interest to point out that van der Waals in his Nobel prize lecture gave credit to Laplace for the argument that pressure is reduced proportional to the square of the density.
Statistical thermodynamics derivation
The canonical partition function Q of an ideal gas consisting of N = nNA identical particles, is
where is the thermal de Broglie wavelength,
with the usual definitions: h is Planck's constant, m the mass of a particle, k Boltzmann's constant and T the absolute temperature. In an ideal gas q is the partition function of a single particle in a vessel of volume V. In order to derive the van der Waals equation we assume now that each particle moves independently in an average potential field offered by the other particles. The averaging over the particles is easy because we will assume that the particle density of the van der Waals fluid is homogeneous. The interaction between a pair of particles, which are hard spheres, is taken to be
r is the distance between the centers of the spheres and d is the distance where the hard spheres touch each other (twice the van der Waals radius). The depth of the van der Waals well is .
Because the particles are independent the total partition function still factorizes, , but the intermolecular potential necessitates two modifications to q. First, because of the finite size of the particles, not all of V is available, but only , where (excluded volume per particle). Second, we insert a Boltzmann factor to take care of the average intermolecular potential. We divide here the potential by two because this interaction energy is shared between two particles. Thus
The total attraction felt by a single particle is,
where we assumed that in a shell of thickness dr there are N/V 4π r2dr particles. Performing the integral we get
Hence, we obtain by the use of Stirling's approximation,
It is convenient to take T out of Λ and to rewrite this expression as
where Φ is a constant. From statistical thermodynamics we know that
- ,
so that, writing
we get,
Other thermodynamic parameters
The extensive volume V is related to the volume per particle v=V/N where N = nNA is the number of particles in the system. As before, we consider structureless particles with three translational degrees of freedom only. The equation of state does not give us all the thermodynamic parameters of the system. We can take the equation for the Helmholtz energy A
From the equation derived above for lnQ, we find
This equation expresses A in terms of its natural variables V and T , and therefore gives us all thermodynamic information about the system. The mechanical equation of state was already derived above
The entropy equation of state yields the entropy (S )
from which we can calculate the internal energy
Similar equations can be written for the other thermodynamic potentials and the chemical potential, but expressing any potential as a function of pressure p will require the solution of a third-order polynomial, which yields a complicated expression. Therefore, expressing the enthalpy and the Gibbs energy as functions of their natural variables will be complicated.
Reduced form
Although the material constants a and b in the van der Waals equation depend on the fluid considered, the equation can be recast into a single form applicable to all fluids.
The critical pressure and critical volume can be computed from the condition that the tangent in the critical point is horizontal and that it is a point of inflection:
This gives
Defining the following reduced variables:
- ,
the van der Waals equation of state given above (with n = 1) can be recast in the following reduced form:
This equation holds for all fluids. Thus, when measured in units of the critical values of various quantities, all fluids obey the same equation of state—the reduced van der Waals equation of state. Van der Waals termed this the principle of corresponding states.
References
- ↑ van der Waals, JD (1873) Over de Continuiteit van den Gas- en Vloeistoftoestand (on the continuity of the gas and liquid state). Ph.D. thesis, Leiden, The Netherlands. [1]
- ↑ J. V. Sengers and J. M. H. Levelt-Sengers, Annual Review of Physical Chemistry, vol. 37, p. 189 (1986)
- ↑ T. L. Hill, Statistical Thermodynamics, Addison-Wesley, Reading (1960), p. 280
- Subpages
- Chemistry Extra Subpages
- Physics Extra Subpages
- Chemical Engineering Subgroup Citable Versions
- Chemistry Approved Extra Subpages
- Physics Approved Extra Subpages
- Citable versions of articles
- Chemistry Citable Version Subpages
- Physics Citable Version Subpages
- All Content
- Chemistry Content
- Physics Content
- Chemical Engineering tag